<![CDATA[WCWRail.com]]>

 

]]> Thu, 09 Feb 2012 14:24:27 +0000 en <![CDATA[Vertical Pin Retainer Cap Removal Tool]]>
On certain cushioning devices it is necessary to remove a retainer cap to access the coupler vertical pin. The Cap Removal Tool fits the two holes in the cap. Fits 1/2" drive ratchet or breaker bar.  Part No. 0074
]]> <![CDATA[Friction Block Retaining Pin]]>
Friction blocks must be compressed and pinned any time repairs are made to the bolster or side frames of a ride control truck. Our Friction Block Retaining Pins are made of heat-treated tool steel. The T-handle gives a positive grip when installing or removing, along with a
tapered point that helps guide the pin in. 
Item # MLW0137
]]> <![CDATA[Buckey / Friction Block Retaining Pin]]> Part No. 0128

]]> <![CDATA[Draft Gear Assembly Installation fixture]]>

The Draft Gear Assembly Installation fixture may be used with any forklift having a rated capacity of 4,000 lbs. or greater. The rotating head allows quick, simple position of the assembly. The fixture is long enough to allow access from either the front or sides of the freight car. Item # 0334

]]> <![CDATA[Magnet Lifter]]> Capacity: This magnet has a maximum rated capacity of 1,000 pounds for flat material, and a maximum of 500 pounds for round material
 
This magnet is designed to handle flat and round steel materials, and freight car or locomotive repair components. It may be used with any overhead crane, or forklift equipped with a lifting hook. It is equipped with a secondary handle locking system to reduce the chance of inadvertent load release. Item #0410
]]> <![CDATA[Cooling Fan J Hooks]]>
J-Hooks are used to secure the upper and lower portions of the cooling fans on SD70ACE series locomotives. The hooks prevent the lower portion from separating during handling and transport. The hooks are used and sold in sets of four. Item # 0409
]]> <![CDATA[304 Rotating Coupler Lifter]]>
Designed to Lift the 304 rotating couplers.
After removing the knuckle and cross key or connection pin, turn coupler one quarter turn clockwise by hand and attach the coupler lifter, securing it with the two fixture attachment pins. Item # 0405
 
]]> <![CDATA[Clam Shell Door Opener]]>
Design to open and close auto rack Clam Shell
Doors having a 3/4" square opening on the lock mechanism Item # 0116
]]> <![CDATA[Air Brake Vent Protector Removal Tool]]>

The new vent protector Removal Tool is compatible with both the plastic and aluminum protectors. It provides a positive grip and the leverage necessary for removal. Attaches to any 1/2" drive ratchet. Item # WCWN6832B

]]> <![CDATA[Battery Pusher]]>
These pushers are used as a pair to move batteries
 back into place in the locomotive battery
compartment using a forklift. Item # 0338
 
]]> <![CDATA[Locomotive Handrail Gate]]> This gate is used as to provide fall protection for the area located
between the locomotive handrail stanchions  Item # 0372
 
]]> <![CDATA[Key Knocker]]>
Hand held cotter key remover with hand guard.
Insert the point into the eye of the cotter key
 and strike with hammer to remove.
12" Long with Hand Guard Item # 0299  $37.02
       With Out Hand Guard Item # 0299-2 $25.26
24" Long with Hand Guard Item # 0299-1 $89.30
       With Out Hand Guard Item # 0299-3  $69.89
]]> <![CDATA[Cotter Key Bender]]>
We offer three styles of Cotter Key Benders.
 
Item # 0070 has a configuration insert at each end that holds the cotter key as you bend it, for 3/8" and 1/2" Cotter Pins
$ 27.95
 
Item# WCW-690 Has a hex shape body with a curved pointed end for hole alignment. Fits 3/8" cotter pins.
$ 33.21
 
Item# 0331 fits only 3/8" cotter pins, has a knurled
handle with insert. Pointed end for hole alignment.
$ 22.59
 
 

 
]]> <![CDATA[Coupler Storage Racks]]> Holds both E and F couplers
 
10 Unit E&F Coupler Rack
Height 45" Width 42" Length 109"
Item # 0285 $ 1,987.71
 
 
 
 
 
17 Unit E&F Coupler Rack
Height 63" Width 63" Length 137"
Item # 0337 $ 2,872.84
 
 
 
 
 
 
10 Unit Long Shank Coupler Rack
Height 49" Width 72" Length 118"
Item # 0416 $ 3,696.56
 
 
 
 
 
 
 
10 Unit Locomotive Coupler Rack
Height 48" Width 42" Length 118"
Item # 0417 $ 2,600.72
 
 
 
 
 
]]> <![CDATA[Broken Pipe & Screw Extractors]]>
These tools feature a four-point grip.
assuring a strong bite with less expansion.
From 1/8" to 2" pipe and 3/8" - 3-1/2" Screw
Carrying case included Item # 0418
]]>